What is plinth area in construction?
Plinth area is the built-up covered area of a building measured at floor level, including the thickness of its walls. Under IS 3861 it is taken to the outer face of the external walls, floor by floor. Estimators use it for preliminary cost estimates, and authorities use it to check what has been built.
Key facts
- Unit
- Square metres (m²), often converted to sq ft
- Measured at
- Floor level of each storey and basement, to the outer face of walls
- Where it appears
- Preliminary estimates, plinth area rates, sanction drawings, valuation
- Governing standard
- IS 3861:2002; local bylaws may define areas differently
How do you calculate plinth area?
Measure each floor to the outer face of its external walls at floor level, add the parts IS 3861 includes, leave out the parts it excludes, and repeat for every floor and basement.
Worked example for one floor, using the IS 3861 rules below:
| Part | Working | Area |
|---|---|---|
| Main building, outer face of walls | 12.00 m × 9.00 m | 108.00 m² |
| Balcony covered by a projection above | 3.00 m × 1.20 m, full area | 3.60 m² |
| Balcony open to the sky | 2.00 m × 1.20 m = 2.40 m², half the area | 1.20 m² |
| Plinth area | 108.00 + 3.60 + 1.20 | 112.80 m² |
112.80 m² × 10.7639 = 1,214.17 sq ft. Cornices, flower-pot slabs and similar architectural projections, and the open terrace, add nothing.
What does IS 3861 include and exclude in plinth area?
It includes the wall area at floor level, service shafts, staircases, and balconies and open verandahs covered by a projection above, with half the area of uncovered ones. It excludes lofts, cornices and architectural projections, open platforms, terraces and open spiral or service stairs.
IS 3861 also leaves out plinth offsets when taking the wall area, and counts only half of a wall shared with a neighbour. Alcoves made by cantilevering a slab are counted in steps by their height. Each category (basement, stilt floor, mezzanine, garage, mumty and so on) is measured separately rather than clubbed together.
Plinth area vs built-up area vs carpet area
In IS 3861, plinth area is the built-up covered area, so the two describe the same measurement there. Carpet area is smaller: it is the usable floor inside the walls.
| Term | What it measures | Defined in |
|---|---|---|
| Plinth area | Covered area at floor level, walls included | IS 3861:2002 |
| Built-up area | Usually the same idea; contracts and bylaws vary in what they add | The agreement, sanction plan or bylaw |
| Carpet area | Net usable floor area of an apartment | RERA Act 2016, Section 2(k), for apartment sales |
IS 3861 has its own carpet area definition for buildings, which is not the same as the RERA one. Say which definition a figure uses. No fixed percentage converts one area into another.
What is a plinth area estimate?
A plinth area estimate multiplies the plinth area by a cost per unit area for that type of building. It is a preliminary estimate, not a substitute for a BOQ measured from drawings.
CPWD publishes plinth area rates for this purpose alongside its schedule of rates; our CPWD DSR guide explains how the schedules fit together. For a house, the house construction cost calculator works the same way from built-up area per floor, and the house cost guides by size break that into materials.
Go deeper
Related terms
Sources
- IS 3861:2002, method of measurement of plinth, carpet and rentable areas (BIS)
- Real Estate (Regulation and Development) Act, 2016, Section 2(k)
Checked 2026-11-03. Contract documents, tender conditions and the structural drawings for your project take precedence over the general rules on this page.