Skip to main content
Honeycombing: Honeycombing in Concrete

What is honeycombing in concrete?

Honeycombing is a patch of hardened concrete where the coarse aggregate shows with open voids between the stones, because cement mortar did not fill the gaps. It appears when the formwork is stripped. The usual causes are poor compaction, slurry leaking from the formwork, segregation and congested reinforcement. It weakens the member and exposes steel.

Key facts

Also called
Honeycomb, voids, rock pockets
Where it shows
Column bases, beam-column joints, edges and soffits, and wherever bars are congested
Prevention
IS 456 clauses 11.1 (tight formwork), 12.6, 13.2 and 13.3 (placing and compaction)
Recorded in
Pour inspection records and a non-conformance report (NCR)

What causes honeycombing in concrete?

Mortar fails to fill the space between the coarse aggregate, because the concrete was not compacted, the slurry leaked out of the formwork, the mix segregated, or the bars were too close for the concrete to pass.

  • Poor compaction. No vibrator, too short a vibration, or a needle that cannot reach.
  • Leaking formwork. IS 456 clause 11.1 requires formwork that prevents loss of slurry; gaps at joints and ties let the mortar run out.
  • Segregation. Dropping concrete from a height or over-wet mixes separate the stones from the mortar. IS 456 clause 13.2 gives 1.5 m as general guidance for the maximum free fall.
  • Congested steel. Clause 12.6 asks for reinforcement placed so concrete can be placed without segregation and compacted with an immersion vibrator.
  • Stiff or late concrete. Concrete placed after initial set, or too stiff for the section, does not flow round the bars.

How do you prevent honeycombing?

Use tight formwork, a workable mix, short drops and thorough vibration, and check the reinforcement leaves room for the vibrator before the pour.

IS 456 clause 13.3 asks for concrete to be thoroughly compacted and fully worked around the reinforcement, embedded fixtures and into the corners of the formwork, using mechanical vibrators. It also warns that over-vibration and under-vibration are both harmful. In practice:

  1. Seal formwork joints and tie holes; our shuttering guide lists the checks.
  2. Fix cover blocks so bars do not touch the formwork.
  3. Place concrete in layers near its final position and vibrate each layer.
  4. Watch column bases and joints, where both mortar loss and congestion are worst.

How is honeycombing repaired?

The structural engineer decides from the depth, extent and location. Shallow surface honeycombing is usually cut back to sound concrete and patched; deep or extensive voids in a load-bearing member need investigation before any repair.

Plastering over honeycombing hides it without fixing it: the voids stay, and water reaches the steel. A typical sequence for a minor patch is to cut out loose material to sound concrete, clean and wet the surface, and fill with a repair mortar the engineer approves, then cure it. For deep voids, the engineer may ask for testing before deciding on grouting, jacketing or recasting. Record each case and its fix, because it will come up again at handover.

Who pays for honeycombing repairs?

Normally the contractor who placed the concrete, because the work does not meet the specification. The contract sets the procedure: rectification, replacement or acceptance at a reduced rate.

On CPWD works, GCC 2023 Clause 16 deals with work not done as per specifications, and Schedule F names the competent authority for deciding reduced rates. Private work orders should state the same: who decides, how the repair is measured, and that rectification is not paid as an extra.

A repair item never belongs in the BOQ as new work. If a contractor bills for "honeycomb repair", check the contract before you certify it.

Go deeper

Related terms

Sources

Checked 2026-11-03. Contract documents, tender conditions and the structural drawings for your project take precedence over the general rules on this page.

All construction terms in the glossary