What is clear cover in construction?
Clear cover is the thickness of concrete between the outside face of a concrete member and the surface of the nearest reinforcing bar, usually the stirrup or link. IS 456 calls the design value nominal cover. It protects the steel from corrosion and fire, and its value depends on the exposure condition and the member.
Key facts
- Also called
- Concrete cover; IS 456 term: nominal cover
- Measured to
- All steel, including links (IS 456, clause 26.4.1)
- Values
- 20 mm (mild) to 75 mm (extreme) by exposure, IS 456 Table 16; 50 mm in footings; 40 mm for column main bars
- Where it appears
- General notes on structural drawings, BBS cutting lengths, pre-pour checks
What is the clear cover for slab, beam, column and footing?
IS 456 sets a minimum nominal cover by exposure: 20 mm mild, 30 mm moderate, 45 mm severe, 50 mm very severe and 75 mm extreme. Footings need at least 50 mm and column main bars at least 40 mm, whatever the exposure.
| Case | Minimum nominal cover | IS 456 reference |
|---|---|---|
| Mild exposure | 20 mm | Table 16 |
| Moderate | 30 mm | Table 16 |
| Severe | 45 mm | Table 16 |
| Very severe | 50 mm | Table 16 |
| Extreme | 75 mm | Table 16 |
| Footings | 50 mm | 26.4.2.2 |
| Column longitudinal bars | 40 mm, and not less than the bar diameter | 26.4.2.1 |
Table 16 also allows 5 mm less for main bars up to 12 mm in mild exposure, and 5 mm less in severe and very severe exposure where the concrete is M35 or above. Columns of 200 mm or less with bars not over 12 mm may use 25 mm. The cover for a required fire rating comes from Table 16A and may be larger. The structural drawing's general notes state the cover for each member; use those.
Clear cover vs nominal cover vs effective cover
Clear cover and nominal cover both run from the concrete face to the outermost steel; nominal cover is the IS 456 design value shown on drawings. Effective cover runs to the centre of the main tension bars.
| Term | Measured from the concrete face to | Used for |
|---|---|---|
| Clear cover | The surface of the nearest bar | Site checks, cover block size |
| Nominal cover (IS 456) | All steel including links; never less than the bar diameter | Drawings and design |
| Effective cover | The centroid of the main tension bars | Effective depth in design |
IS 456 defines effective depth as the distance from the centroid of the tension reinforcement to the extreme compression fibre (clause 23.0). Some site notes give "clear cover to main bars" instead of cover to links. Read the general note carefully: the difference is the stirrup diameter.
How do you calculate effective cover and effective depth?
Effective cover is the nominal cover plus the link diameter, if any, plus half the main bar diameter. Effective depth is the overall depth minus the effective cover.
Slab: 125 mm thick, mild exposure with 20 mm nominal cover on the drawing, 10 mm main bars, no links. Effective cover = 20 + 10 ÷ 2 = 25 mm; effective depth = 125 − 25 = 100 mm.
Beam: 450 mm deep, moderate exposure with 30 mm nominal cover to the 8 mm stirrups, 16 mm main bars in one layer. Cover to the main bar = 30 + 8 = 38 mm; effective cover = 30 + 8 + 16 ÷ 2 = 46 mm; effective depth = 450 − 46 = 404 mm.
How is cover checked on site and in the BBS?
On site, cover blocks of the nominal cover size hold the steel, and the actual cover may exceed the nominal by up to 10 mm but never fall short. In a BBS, cover sets the bar and stirrup dimensions.
IS 456 clause 12.3.2 asks for spacers of the same nominal size as the nominal cover, placed at most 1 m apart; see cover block. Check the cover at edges, corners and column faces before the pour.
In the bar bending schedule, a stirrup's outer dimensions are the member size less the cover on each face, and straight bars stop short of the faces by the cover. Cover also enters development length and lap length checks where bars are anchored near a face.
Common mistakes with clear cover
The usual mistakes are reading cover to main bars where the drawing means cover to links, using slab cover blocks in footings and columns, and forgetting the fire-rating cover.
- Main bar vs link. Cover to links is the IS 456 meaning; check which the note uses.
- One size for everything. Footings need at least 50 mm; slabs in mild exposure may need 20 mm.
- Fire cover. Table 16A can need more than Table 16.
- No tolerance below. IS 456 allows +10 mm, not −1 mm.
Go deeper
Related terms
Sources
Checked 2026-11-03. Contract documents, tender conditions and the structural drawings for your project take precedence over the general rules on this page.