Skip to main content
Chajja: Chajja / Sunshade

What is a chajja in construction?

A chajja is a thin projecting sunshade, usually of reinforced concrete, built over a window or door to keep rain and sun off the opening. It is often cast with the lintel. IS 1200 treats a projection up to 100 mm average thickness as a chajja; a thicker one is measured as a slab.

Key facts

Also called
Sunshade, weather shade or chhajja
Concrete unit
Cubic metres (IS 1200 Part 2)
Shuttering unit
Sq m of contact surface, including edges (IS 1200 Part 5)
Thickness rule
Up to 100 mm average thickness is a chajja; over 100 mm is measured as slab

How is a chajja measured in a BOQ?

Its concrete is measured in cubic metres, its shuttering in square metres and its steel in kg, each as a separate item. Where it is cast with a lintel, beam or slab, only the clear projection is measured as chajja.

IS 1200 Part 2, as amended in 1984, sets the rules in clause 4.2.3. A chajja on its own is measured inclusive of its bearing on the wall. Combined with a lintel, beam or slab, it is measured as the clear projection, so the part inside that member is measured with it. Where vertical fins or fascias meet a chajja, the chajja is measured clear between them and the fins are measured through (4.2.3.1).

IS 1200 Part 5 lists weather shades and chajjas, including edges, as their own shuttering category (5.1 q), measured by the actual surface in contact with concrete (6.1). Our RCC rate guide notes that BIS issued a revised Part 2 in 2025, so check the edition your contract adopts.

How do you calculate chajja concrete and shuttering?

Multiply the clear projection by the length and the average thickness for concrete, and add the soffit and edge areas for shuttering. The example below comes to about 0.08 m³ of concrete and 1.12 m² of shuttering.

Assumed chajja: cast with a lintel, 0.6 m clear projection, 1.5 m long, 100 mm thick at the root and 75 mm at the tip.

StepWorkingResult
Average thickness(100 + 75) ÷ 287.5 mm, under 100 mm, so chajja
Concrete0.6 × 1.5 × 0.08750.07875 m³, 0.08 m³ to the nearest 0.01
Soffit shuttering0.6 × 1.50.90 m²
Front edge1.5 × 0.0750.1125 m²
Two end edges2 × 0.6 × 0.08750.105 m²
Total shuttering0.90 + 0.1125 + 0.1051.1175 m², 1.12 m²

IS 1200 Part 2 works cubic contents to the nearest 0.01 m³ (clause 2.4.3). The dimensions are an example; take yours from the drawing.

Chajja vs lintel vs slab

A lintel spans the opening and carries the wall above it; a chajja projects outward as a sunshade. A projection thicker than 100 mm on average is measured as a slab, in the same class as balconies and canopies.

The thickness test comes from the note to IS 1200 Part 2 clause 4.2.3, and the rate changes with the class. See lintel for how lintels, lintel bands and chajjas are measured when they are cast together.

Where does the steel go in a chajja?

A chajja is a cantilever, so its main bars run across the projection near the top face and are anchored back into the lintel or beam, with distribution bars along its length. The structural drawing gives the bar sizes and anchorage.

In a BBS, each main bar is a bent shape, and its cutting length is the legs after cover plus the anchorage the drawing asks for, minus the bend deductions. Do not guess the anchorage; read it from the drawing.

Does a chajja reduce the brickwork quantity?

Only when its bearing is large. IS 1200 Part 3 makes no deduction from brickwork for the bearings of slabs and chajjas up to 10 cm thick that do not run through the wall.

That is clause 4.1.4. A thicker bearing, or one through the full wall, is deducted. Our brickwork rate guide and IS 1200 guide list the other no-deduction items.

Go deeper

Related terms

Sources

Checked 2026-11-03. Contract documents, tender conditions and the structural drawings for your project take precedence over the general rules on this page.

All construction terms in the glossary