What is bend deduction in a bar bending schedule?
Bend deduction is the length subtracted from the sum of a bar's outside dimensions at each bend, because a bent bar is shorter along its centreline than along its outer faces. Common site practice takes 1d for a 45° bend, 2d for 90°, 3d for 135° and 4d for 180°, where d is the bar diameter.
Key facts
- Common values
- 45° = 1d, 90° = 2d, 135° = 3d, 180° = 4d
- Status
- Site and teaching approximations, not an IS 2502 table
- Used for
- Cutting lengths of L-bars, U-bars, cranked bars, stirrups and ties
- In our BBS calculator
- Defaults of 1d, 2d and 3d for 45°, 90° and 135°, all editable
What are the bend deduction values for 45°, 90°, 135° and 180°?
1d, 2d, 3d and 4d respectively, where d is the bar diameter. For an 8 mm bar that is 8, 16, 24 and 32 mm.
| Bar diameter | 45° (1d) | 90° (2d) | 135° (3d) | 180° (4d) |
|---|---|---|---|---|
| 8 mm | 8 mm | 16 mm | 24 mm | 32 mm |
| 10 mm | 10 mm | 20 mm | 30 mm | 40 mm |
| 12 mm | 12 mm | 24 mm | 36 mm | 48 mm |
| 16 mm | 16 mm | 32 mm | 48 mm | 64 mm |
Our BBS calculator uses 1d, 2d and 3d for 45°, 90° and 135° bends, and you can edit each one. It has no 180° deduction: a hook at the end of a straight bar is entered as one complete hook allowance instead. IS 2502 Table II gives that allowance as 9d for its k = 2 hook, rounded to the nearest 5 mm and at least 75 mm. Do not add a full hook allowance and then deduct the same bend again.
Is bend deduction given in IS 2502?
No. IS 2502 gives bending dimensions and allowances shape by shape, not one angle-based deduction table. The 1d to 4d values are common site approximations.
IS 2502 Table VIII, shape A, gives a rectangular link as 2(A + E) + 24d, using inside dimensions, with the allowance built in. For an 8 mm stirrup in a 230 × 450 mm beam with 25 mm cover, that gives 2(164 + 384) + 24 × 8 = 1,288 mm, against 1,224 mm by the site shortcut. The two differ because they measure from different faces and allow for bends differently. The approved bend radius and shape detail for your project govern.
Bend deduction is also not the same as the anchorage value of a bend. IS 456 clause 26.2.2.1 credits 4φ of anchorage for each 45° of bend, up to 16φ. That counts towards development length; it does not shorten the bar.
How do you apply bend deduction? (worked examples)
Add the outside leg lengths after cover, then subtract the deduction for each bend. A 12 mm L-bar with legs of 2,950 and 550 mm has one 90° bend, so its cutting length is 3,500 − 24 = 3,476 mm.
| Bar | Working | Cutting length |
|---|---|---|
| 12 mm L-bar, legs 2,950 and 550 mm, one 90° bend | 2,950 + 550 − 2 × 12 | 3,476 mm |
| 12 mm U-bar, legs 2,950, 550 and 550 mm, two 90° bends | 4,050 − 2 × (2 × 12) | 4,002 mm |
| 12 mm bar with two 45° cranks, 150 mm rise each | 2,950 + 2 × (√2 − 1) × 150 − 4 × (1 × 12) | 3,026.264 mm |
| 8 mm stirrup, three 90° bends and two 135° hooks | deduct 3 × 16 + 2 × 24 | 96 mm off the outside lengths |
Each crank has two 45° bends, so two cranks carry four 45° deductions. The legs are the overall sizes minus 25 mm cover at each end, as in the calculator's worked examples.
Why is bend deduction needed?
Because BBS shape dimensions are usually outside dimensions. At each bend the outer faces run longer than the bar's centreline, so adding outside dimensions overstates the steel needed.
If a drawing or schedule gives centreline dimensions and bend arcs instead, the deduction is already allowed for; do not apply it again. Too little deduction gives bars that are too long to fit inside the cover; too much gives bars that fall short of their laps and anchorage.
Common mistakes with bend deduction
The usual ones are deducting a hook's bend after adding a complete hook allowance, applying deductions to centreline dimensions, and using the 135° value for 90° bends.
- Hook counted twice. A complete hook allowance already includes its bend.
- Centreline dimensions. Deduct only from outside dimensions.
- Wrong angle. A stirrup has three 90° bends and two 135° hooks.
- Rounding first. Work out the length, then round the scheduled length up to 25 mm if your schedule does so (IS 2502, clause 5.1.1).
Go deeper
- Bar bending schedule (BBS) guide
- BBS calculator with editable bend deductions
- Worked BBS examples for slab, beam, column and footing
Related terms
Sources
- SiteSetu: BBS calculator conventions (1d, 2d and 3d deductions; 135° hook max(10d, 75 mm); IS 13920 editions)
- SiteSetu: BBS guide (bend deduction 1d, 2d, 3d and 4d; worked beam and column links)
- IS 2502:1963, clause 5.1.1, Table II hook allowances and Table VIII shape A (BIS)
- IS 456:2000, clauses 26.2.1, 26.2.1.1, 26.2.2.1, 26.2.5.1 and 38.1 (BIS)
Checked 2026-11-03. Contract documents, tender conditions and the structural drawings for your project take precedence over the general rules on this page.